Special designed holder incorporates thick nylon web straps that secures your Fire Extinguisher to the roll bar. Straps are fully adjustable and secure with hook and loop fasteners and will hold up to a 4 diameter fire extinguisher. Fits up to a 3 roll bar with or without padding.
|
Mag-Hytec's heavy duty differential covers and transmission pans provide increased lubricant and cooling capacity for hard working recreational and service vehicles. Mag-Hytec covers and pans set your vehicle apart in both aesthetics and function cast in A356-T6 aluminum and texture powder coated black With machined cooling fins. Magnetic drain plugs trap worn gear material promoting fluid integrity. Each unit is fitted with ARP 568 O-rings for superior sealing. All hardware is 303 stainless steel, in most applications no gasket or sealant is required, and all Mag-Hytec parts are covered by a lifetime limited warranty. Depend on Mag-Hytec when you're pulling a heavy load.
For Use On GM 8.5in./8.6in. Rear Axles Only
Finned Aircraft Aluminum Housing For Improved Cooling
Black Powder Coat Finish
Holds 2 Extra Quarts Of Oil
Overall Height Is 3 1/4in.
Offers Easy Routine Maintenance Without Removing The Differential Cover
Dipstick With Magnetic Insert
|
Poison Spyder Bombshell Diff Covers are designed to protect your gears, lockers and diff cover bolts from the most punishing rocks and trail hazards. The stock covers your Jeep came with are weak, stamped sheetmetal. Even a moderate tap with a rock can cave it in against your ring gear, causing potential damage to the gears, locker and carrier bearings, not to mention a difficult, messy trail fix. Even more common, though less catastrophic, is "peel back" that can occur when sliding over a rock causes the lip of the cover to peel up, allowing your gear oil to drain causing a hazard for both your Jeep and the environment. The Bombshell Diff Cover is your best insurance against each of these hazards. The Bombshell differential cover is cast from highly ductile nodular iron—the same material drag racing differential housings are cast from to handle thousands of horsepower. The design of the Bombshell incorporates recesses to protect the diff cover bolt heads from trail damage, while the profile of the Bombshell acts as a ramp to help slide your Jeep up and over the most troublesome pumpkin-eaters. The ramp profile also results in an extremely thick & up to 1" thick—cross-section around the bolt ring, where contact with the rocks is most likely. Throughout the rest of its cross-section the Bombshell is the thickest cast differential cover on the market, from 7/16" to a brutal 1/2" thick at the outermost surface. Dana 44;Cast ductile nodular iron;Bare steel;Thickest cast differential cover
|
This handy 2.5 pound fire extinguisher holder will keep your extinguisher stored safely and securely to your off-road rig's 2-3 inch roll bar and off of the floorboard during dicey off-road driving conditions.
Use with 1.5-4 inch Sport/Roll Bar
Attaches using heavy-duty hook and loop straps
Works with 2.5 pound Fire Exinguishers
Available in black only
|
For those looking to further enhance the JK 4-Door Trail Cage installation, the Poison Spyder C-Pillar Kit ads strength to the rear passenger portion of the OE cage. This kit must be welded in to the OE cage at the top, but it bolts in at the lower end. The C-Pillar kit consists of CNC laser cut lengths of 1.75" OD, .120" wall DOM tubing, and engineered foot plates that are fabricated from CNC laser cut, brake-formed 3/16" plate steel. Convenient indexing tabs and slots are provided where the DOM tube connects with the foot plate, making assembly quick and easy.
|
Trail-Gear O.D. Tube Clamps are ideal for suspension and steering brackets that you need attached to a section of tubing when you don’t want to weld the bracket directly to the tubing because adjustment or frequent removal of the bracket is needed. The O.D. Tube Clamp is perfect for attaching shock brackets to suspension link or steering brackets to steering rods or links and allows you to attach steel mounting brackets that are readily available to aluminum suspension links and steering rods that you could not otherwise weld steel brackets to. Manufactured from 1020 steel, with a clamping force of up to 8,600lbs these tube clamps will not fail even under the most extreme circumstances. Sold Individually.
|
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
|
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
|
HalGuard is no ordinary fire extinguisher. It contains an electrically non-conductive"clean" extinguishing agent that rapidly turns into a gas. The clean agent used in HalGuard has passed extensive testing by Underwriters Laboratories, and meets FAA requirements. It can be found on commercial aircraft, and is used by airport fire fighters and on the flight line. Hand held HalGuard extinguishers are available in either compact 1.4 lb. and 2.5 lb. sizes, or larger 5 lb., 11 lb., and 15.5 lb. units. The larger sizes are USCG approved, and meet DOT requirements for the heavy duty truck market. 65 lb., and 150 lb. wheeled HalGuard extinguishers offer maximum clean agent protection for the pit lane or large facilities.
|
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle.
For Use On Ford 8.8in. Rear Axles
Cast From Lightweight Aluminum To Dissipate Heat
Raw Aluminum Finish
ReinForcing Ribs For Added Rigidity And Strength
Heat Treated And Shot Peened To Help Handle A Direct Impact
Fully Machined Seal Surface For A Leak Free Installation
|
Need to place a support tube across your truggy or buggy, but need the flexibility to remove a motor, transmission, or even a seat? We have the perfect solution for you, Trail-Gear’s Interlocking Tube Clamps. They are machined from 100% 4130 Chromoly and use a counter sunk allen head screw.
|
Weld in frame gussets. Each gusset measures 3" tall by 3" wide. Made from 3/16" mild plate steel.
|
PRO MULTI-PURPOSE FIRE EXTINGUISHER
UL Rate 1-A:10-B:C dry chemical multi-purpose -
fire extinguisher with easy to pull safety pin
Pressure gauge provides at a glance status
Tough impact resistant metal valve, handle -
and lever with powder coated aluminum cylinder
Suitable for use on most common fires
Contains 2.6 lb. average Monoammonium Phosphate
Supplied with wall hanger for fast access
466227 2.6# EXTINGUISHER
COLOR:Red
|
Neoprene Roll Bar Wrap; 2 x 50in lengths; Roll bar Rapz are a neoprene-backed wrap with "hook-and-loop" fasteners. Rapz are designed to wrap around or cover up almost any round or square tube item. This product can not be returned.
|
This handy Roll Bar Mounted Cellphone Holder will keep your cellphone, smartphone or hand-held CB radio stored safely and securely to your off-road rig's 2-3 inch roll bar and off of the floorboard during dicey off-road driving conditions.
|
TIE BAR
|
The F.A.S.T (Functional Agile Survival Trail) is the perfect knife to store in your vehicle for all purposes. The integrated windshield spike in the handle is great for any emergency and gives you a way to break glass to escape the vehicle.
|
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle.
For Use On Dana 25/27/30 Front Axles Except KJ
Cast From Lightweight Aluminum To Dissipate Heat
Raw Aluminum Finish
ReinForcing Ribs For Added Rigidity And Strength
Heat Treated And Shot Peened To Help Handle A Direct Impact
Fully Machined Seal Surface For A Leak Free Installation
|
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle.
For Use On Dana 44 Front Or Rear Asxles
Cast From Lightweight Aluminum To Dissipate Heat
Raw Aluminum Finish
ReinForcing Ribs For Added Rigidity And Strength
Heat Treated And Shot Peened To Help Handle A Direct Impact
Fully Machined Seal Surface For A Leak Free Installation
|
This handy 1.5 pound fire extinguisher holder will keep your entinguisher stored safely and securely to your off-road rig's 2-3 inch roll bar and off of the floorboard during dicey off-road driving conditions.
Use with 1.5-4 inch Sport/Roll Bar
Attaches using heavy-duty hook and loop straps
Works with 1.5 pound Fire Exinguishers
Available in black only
|
Clear instruction label using graphics to show steps required to operate extinguisher. Easy-to-read gauge tells you fire extinguisher is charged and ready for use. Easy-to-pull safety pin, rust and impact resistant nylon handle. Material(s): Aluminum; Sodium Bicarbonate; Fire Class: BC; UL Rating: 10-B:C; Unit Weight: 3.9 lbs.
|
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle.
For Use On Dana 50/60/70 Front Or Rear Axles
Cast From Lightweight Aluminum To Dissipate Heat
Raw Aluminum Finish
ReinForcing Ribs For Added Rigidity And Strength
Heat Treated And Shot Peened To Help Handle A Direct Impact
Fully Machined Seal Surface For A Leak Free Installation
|
Part Number: S/BROLLBAR1
Includes the following: First Aid Storage Bag - S/B769541
Full Size Mag Flashlight Holder - S/B769520
2.5 lb. Fire Extinguisher Holder - S/B769540
Deluxe Sport Bar Handles - S/B769301
|
The velcro straps that hold this unit to the roll bar are optimally sized for use on padded roll bars. When using on bare, un-padded tubes (1.75" OD or larger recommended), the ends of the velcro straps wlll be too long, but can either be tucked in or cut off (use a lighter to cauterize the cut edge of the nylon webbing). Black;Holds 2.5lb fire extinguisher;Attaches to roll bar with Velcro
|
HalGuard is no ordinary fire extinguisher. It contains an electrically non-conductive"clean" extinguishing agent that rapidly turns into a gas. The clean agent used in HalGuard has passed extensive testing by Underwriters Laboratories, and meets FAA requirements. It can be found on commercial aircraft, and is used by airport fire fighters and on the flight line. Hand held HalGuard extinguishers are available in either compact 1.4 lb. and 2.5 lb. sizes, or larger 5 lb., 11 lb., and 15.5 lb. units. The larger sizes are USCG approved, and meet DOT requirements for the heavy duty truck market. 65 lb., and 150 lb. wheeled HalGuard extinguishers offer maximum clean agent protection for the pit lane or large facilities.
|
MaxOut™ dry chemical fire extinguishers have a proven track record in extinguishing the types of fires likely to occur in an automotive environment. Models MX250C, MX250R and MX250B utilize a specially fluidized and siliconized mono ammonium phosphate dry chemical. Models MX100C, MX100R and MX100B contain a siliconized sodium bicarbonate based dry chemical with free flowing and non-caking additives. All MaxOut™ models effectively smother and break the chain reaction of fires involving flammable liquids and pressurized gasses, and will not conduct electricity back to the operator. MaxOut™ models MX250C, MX250B and MX250R are also highly effective at stopping fires of common combustibles like wood and paper. Great for marine or residential use.
|
GARAGE / WORKSHOP FIRE EXTINGUISHER
Class 3-A, 40-B:C--For solid combustibles-
flammable liquids and electrical fires
Ideal for home or office
Meets and exceeds 2-A, 10-B:C requirements
50% more Class A fire fighting capacity
5.5 lb. of fire extinguishing agent
Includes UL- approved wall hanger
HAZMAT Item: Not shippable via UPS or FedEx
21005766P 5# ABC FIRE EXTING
SIZE:5.5 Lb.
COLOR:Red/Black
|
G2 aluminum differential covers are designed to not only protect your ring & pinion, they are designed to help cool your gear oil for prolonged bearing life. Made from high strength heat treated aluminum to withstand direct hits, these covers help protect your investment while adding a distinct look to your vehicle.
For Use On Dana 35 Rear Axles
Cast From Lightweight Aluminum To Dissipate Heat
Raw Aluminum Finish
ReinForcing Ribs For Added Rigidity And Strength
Heat Treated And Shot Peened To Help Handle A Direct Impact
Fully Machined Seal Surface For A Leak Free Installation
|
Mount your Hi-Lift® Jack horizontally within easy reach on the roll cage of a Jeep Wrangler JK. No drilling required, mounts directly to the factory roll cage tubing. 6061-T6 structural and anodized aluminum for strength, durability, and a clean look. Specifically designed to mount and secure your Hi-Lift® Jack on the inside rear of a Jeep Wrangler JK. Provides secure interior storage with easy access when needed.
|
Keep your Smittybilt Comp-Air Compact Air System out of the way and easily accessible with this convenient roll bar mount. ROLL BAR MOUNT Attaches to OEM JK rear roll bar and tubes 2.25 inch diameter;Fits Smittybilt Comp-Air Compact Air System;Keep your tank safe and out of the way
|
MaxOut™ dry chemical fire extinguishers have a proven track record in extinguishing the types of fires likely to occur in an automotive environment. Models MX250C, MX250R and MX250B utilize a specially fluidized and siliconized mono ammonium phosphate dry chemical. Models MX100C, MX100R and MX100B contain a siliconized sodium bicarbonate based dry chemical with free flowing and non-caking additives. All MaxOut™ models effectively smother and break the chain reaction of fires involving flammable liquids and pressurized gasses, and will not conduct electricity back to the operator. MaxOut™ models MX250C, MX250B and MX250R are also highly effective at stopping fires of common combustibles like wood and paper. Great for marine or residential use.
|
MaxOut™ dry chemical fire extinguishers have a proven track record in extinguishing the types of fires likely to occur in an automotive environment. Models MX250C, MX250R and MX250B utilize a specially fluidized and siliconized mono ammonium phosphate dry chemical. Models MX100C, MX100R and MX100B contain a siliconized sodium bicarbonate based dry chemical with free flowing and non-caking additives. All MaxOut™ models effectively smother and break the chain reaction of fires involving flammable liquids and pressurized gasses, and will not conduct electricity back to the operator. MaxOut™ models MX250C, MX250B and MX250R are also highly effective at stopping fires of common combustibles like wood and paper. Great for marine or residential use.
|
|
|
|
|
Copyright © 1999-2021 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |